Description:

The GD30DRE518 device integrates a 32-bitARM® Cortex®-M33 core and a 150V threephase gate driver. The device supports multipleapplications, such as motors, electronic bikes,power tools, etc.The device provides up to 512 KB on-chip flashmemory and up to 128 KB SRAM memory. Anextensive range of enhanced I/O and peripheralsconnected to two APB buses. The devices offer 16channel 12-bit ADC, three 12-bit DACs withindependent output channel, 7 channels for DMA0controller and 5 channels for DMA1 controller, Upto 62 fast GPIOs, all mappable on 16 externalinterrupt lines, three fast rail-to-rail low powercomparators with software configurable, two 16-bitadvanced timer, one 32-bit general timer, up totwelve 16-bit general timers, as well as standardcommunication interfaces: SPI, I2C, USART, I2S. 

Features:

• System Core– Integrated 32-bit high performance and lowpower consumption ARM Cortex-M33– Integrated Nested Vectored InterruptController(NVIC)– Up to 180 MHz operation frequency– 24-bit Systick timer

• Memory Map– Up to 512 Kbytes of flash memory– Up to 128 Kbytes of SRAM

• Clock Control– Internal 8 MHz factory-trimmed RC andexternal 4 to 32 MHz crystal oscillator– Internal 48 MHz RC oscillator– Internal 40 KHz RC calibrated oscillatorand external 32.768 KHz crystal oscillator– Integrated system clock PLL

• Power and Reset– Three power domains: VDD, VDDA, VBAKand 1.71 to 3.63 V application supply andI/Os– Three power saving modes: sleep, deepsleep and standby modes– Low voltage detector(LVD)– Reset as power on and power down

• Analog to Digital Converter(ADC)– 16 channel external analog inputs– 12-bit SAR ADC's conversion rate is up to2.5 MSPS– 12-bit, 10-bit, 8-bit or 6-bit configurableresolution– Hardware oversampling ratio adjustablefrom 2 to 256x improves resolution to 16-bit– Input voltage range: VREF- to VREF+

• Digital to Analog Converter(DAC)– Three 12-bit DACs with independent outputchannels– 8-bit or 12-bit mode in conjunction with the DMAcontroller

• DMA– 7 channels for DMA0 controller and 5 channelsfor DMA1 controller– Peripherals supported: Timers, SHRTIMER,ADCs, DACs, SPIs, I2Cs, I2S and USARTs

• GPIOs– Up to 62 fast GPIOs, all mappable on 16external interrupt lines– Analog input/output configurable– Alternate function input/output configurable

• Timer and PWM Generation– Two 16-bit advanced timer (TIMER0(Internal),TIMER7), one 32-bit general timer (TIMER1), upto twelve 16-bit general timers(TIMER2~TIMER4, TIMER8~TIMER16)– Up to 4 independent channels of PWM, outputcompare or input capture for each general timerand external trigger input– 16-bit, motor control PWM advanced timer withprogrammable dead-time generation for outputmatch– 24-bit SysTick timer down counter– 2 watchdog timers (free watchdog timer andwindow watchdog timer)

• Real Time Clock(RTC)– 32-bit programmable counter with aprogrammable 20-bit prescaler– Alarm function– Interrupt and wakeup event

• Inter-Integrated Circuit(I2C)I2C1:– Support both master and slave mode with a frequency up to 1 MHz (Fast mode plus)– Provide arbitration function, optional PEC(packet error checking) generation andchecking– Supports 7-bit and 10-bit addressing modeand general call addressing mode– SMBus 2.0 and PMBus compatible– Supports SAM_V modeI2C2:– Support both master and slave mode witha frequency up to 1 MHz (Fast mode plus)– Provide arbitration function, optional PEC(packet error checking) generation andchecking– Supports 7-bit and 10-bit addressing modeand general call addressing mode– SMBus 3.0 and PMBus 1.3 compatible– Wakeup from Deep-sleep mode onaddress match

• Serial Peripheral Interface(SPI)– Up to three SPI interfaces with a frequencyof up to 22.5 MHz– Support both master and slave mode– Hardware CRC calculation and transmitautomatic CRC error checking– Quad-SPI configuration available in mastermode (only in SPI0)

• USARTUSART0~2, UART3~4:– Maximum speed up to 22.5 MBits/s– Supports both asynchronous and clockedsynchronous serial communication modes– IrDA SIR encoder and decoder support– LIN break generation and detection– ISO 7816-3 compliant smart card interfaceUSART5:– Maximum speed up to 22.5 MBits/s– Supports both asynchronous and clockedsynchronous serial communication modes– IrDA SIR encoder and decoder support– LIN break generation and detection– ISO 7816-3 compliant smart card interface– Dual clock domain– Wake up from Deep-sleep mode

• Comparators(CMP)– Three fast rail-to-rail low-power comparators withsoftware configurable– Programmable reference voltage (internal orexternal I/O)

• Controller Area Network(CAN)–Three CAN interfaces supports the CAN protocolsversion 2.0A and B, ISO11891-1:2015 andBOSCH CAN FD specification with baud ratesup to 1 Mbit/s when classical frames and 6Mbit/s when FD frames–Supports CAN FD Frame with up to 64 data bytes(ISO11898-1 and Bosch CAN FD specificationV1.0)

• Debug mode– Serial wire JTAG debug port (SWJ-DP)

• Motro Driver– High-end floating bootstrap power supply design,with a voltage withstand capability of 150V– Supports the highest frequency of 500KHz– Built-in dead-time control circuit– Upper and lower bridge power supply undervoltage protection, with start and protectionpoints at 4.4V and 4.1V– Internally integrated low-internal-resistancebootstrap charging diode– Output pull and sink current Io+/Io- is +1.0A/-1.3A– HIN input active high, controls the upper bridgeHO output– LIN input active high, controls the lower bridgeLO output– Under Voltage Protection

• Package: QFN88

• RoHS Compliant and Halogen-Free

Applications:

• Brushless DC motor control

• Permanent magnet synchronous motor control

• Servo motor control

• Robotics and RC toys

• Industrial automation